#CANNOT RELOAD NETATALK SERIAL NUMBER#

I think the issue might be in my linux system I use to connect to the pi? The hostname is also raspberrypi so that is not the issue. Sep 28 12:31:45 raspberrypi avahi-daemon: Registering new address record for 10.42.0.56 on eth0.IPv4. Sep 28 12:31:45 raspberrypi avahi-daemon: New relevant interface eth0.IPv4 for mDNS. Sep 28 12:31:45 raspberrypi avahi-daemon: Joining mDNS multicast group on interface eth0.IPv4 with address 10.42.0.56. Sep 28 12:31:34 raspberrypi avahi-daemon: Registering new address record for fe80::a3a0:c51a:4fa:5bd0 on eth0.*. Sep 28 12:31:34 raspberrypi avahi-daemon: New relevant interface eth0.IPv6 for mDNS. Sep 28 12:31:34 raspberrypi avahi-daemon: Joining mDNS multicast group on interface eth0.IPv6 with address fe80::a3a0:c51a:4fa:5bd0. Sep 28 12:31:21 raspberrypi avahi-daemon: Interface eth0.IPv4 no longer relevant for mDNS. Sep 28 12:31:21 raspberrypi avahi-daemon: Leaving mDNS multicast group on interface eth0.IPv4 with address 10.42.0.56. Sep 28 12:31:21 raspberrypi avahi-daemon: Withdrawing address record for 10.42.0.56 on eth0. Sep 28 12:31:21 raspberrypi avahi-daemon: Interface eth0.IPv6 no longer relevant for mDNS. Loaded: loaded (/lib/systemd/system/rvice enabled vendor preset: enabled)Īctive: active (running) since Mon 12:01:52 CEST 35min agoĬGroup: /system.slice/rvice on the pi, the avahi-deamon is $ service avahi-daemon status I want to ssh into my Pi and I can do it right now with the ip address of the Pi. Moreover, if I leave ssh.service and reboot it also doesn't work. However, if I reboot the device, it stops working again. Moreover, if I then remove ssh.service and run systemctl again, it recognizes that ssh.service is gone, and removes that service, but leaves myservice completely functional. However, and this is where it gets weird: if I copy the default ssh.service over from the avahi documentation and then RERUN the systemctl command above, it recognizes a 'change' in the service files, reloads and then BOTH ssh and myservice are published correctly. It just doesn't publish my service (despite the log saying it read my config file).

This should work on boot (according to all the documentation I've seen), but doesn't. I added rvice in /etc/avahi/services with the following content: For that I need to add it to a config, so I did just that. It works just fine, but that doesn't configure it to start automatically. It sorta works, but not quite, and I cannot figure out why not.Īvahi-publish -s myservice _mqtt._tcp 1883 However I can no longer login to the web interface.I am trying to configure avahi-daemon on my raspberry pi to broadcast the service I just programmed, which needs to be discoverable automatically. Now at last the RAID array is accessed and the system is on the network with its original IP address Then upgraded the BIOS and disabled the C1E.

#CANNOT RELOAD NETATALK SERIAL NUMBER#

I have used the loader synoboot 6.2 put in new files on the 2nd partition (from DSM_DS3615xs_24922.pat), set the pid, vid, serial number (as it was on 5.2) and MAC address. Using the old boot stick the system would not boot giving messages about files not found in /tmpĪfter a lot of grief, to make a new XPENology boot stick I now get the problem below. On an HP N40L I followed the promptsand upgraded from 5.2 to 6.

Cannot reload netatalk